Relayed vs Inline: Measuring the Update-Rate Trade-off in Bluetooth Channel Sounding
Relayed vs Inline: Measuring the Update-Rate Trade-off in Bluetooth Channel Sounding
Sep 2026

An accurate distance measurement solves only half of the problem. The other half is cadence: a rate of a few updates per second can log where an asset was; a rate of dozens can follow it, close a control loop around it, and react while the reaction still matters. When engineers evaluate Bluetooth® Channel Sounding, accuracy usually gets the attention, but once the accuracy bar is met, the update rate decides what the application can do.
The update rate is not only a question of scheduling. Channel Sounding offers two ways to move the reflector’s measurement data to the initiator, and the two behave very differently under load. In our bench tests, that difference is the difference between holding your update rate and shedding it.
Every Channel Sounding exchange measures the phase of radio tones between the two devices, initiator and reflector. Each side records what it hears; the reflector’s per-tone measurement is called the Phase Correction Term (PCT). Each device’s radio shifts the phase by its own small amount, and combining the two devices’ measurements cancels those shifts, exposing the channel’s phase along the full round trip, the information the distance calculation needs.
That leaves one design question: how does the reflector’s PCT reach the initiator? The standard answer moves it as data over the connection. The newer answer removes the journey altogether, and with it, much of the update-rate ceiling the standard answer imposes.
Channel Sounding supports two data paths for the reflector’s PCT. Our firmware ships both as variants, so to keep the two straight: throughout this piece, RAS means the standard relayed path and IPT means the newer inline path.
Relayed: Ranging Service (RAS). The initiator reads the reflector’s ranging data, PCT included, over the Ranging Service (RAS), an adopted GATT service, in real-time or on-demand mode, then reassembles it, combines it with its own PCT, and computes the distance.
Inline: Bluetooth® Core 6.3 Inline PCT Transfer (IPT). The reflector applies its measured PCT to the phase of the tones it transmits, so the initiator measures the combined phase directly on reception. The reflector’s PCT report shrinks to an amplitude reading, the relay leg disappears, and distance computation starts as soon as each ranging procedure completes.
What changes on the wire:
We ran both data paths on the bench: a pair of Nordic nRF54L15 development kits with single antennas and a pair of Ezurio BL54L15U modules each with dual antennas (four-antenna-paths), each pair running the same MARS firmware release line, changing nothing but the data path.
Out of the box, the two paths are indistinguishable: in our bench tests, both RAS and IPT delivered about 3 distance updates per second at the shipped default cadence.
Push the update rate harder, and they separate:
The mechanism that the measurements can support: the inline path has no return leg to congest, so the connection time the relay would have consumed goes directly into additional ranging procedures. The relayed path has to move the data it produces first, and at rate, that is where it stalls.
Accuracy is not the trade-off we thought possible. On our 12 m cable-car reference campaign, both data paths passed the sub-metre bar, 2σ accuracy between 0.67 and 0.83 m across the measured board combinations, same algorithm, both data paths. What separates the two paths is not how well they measure; it is how much of the update rate survives load.
How we measured. Update rate: stationary bench pairs, with the update rate pushed progressively higher, once per data path. Accuracy: a 12 m cable-car campaign moving the pair along a reference track. Full configuration and raw data on inquiry.
The choice is not which path is better; it is which constraint binds your design.
A practical rule from the bench: if your update-rate requirement sits near what the shipped default delivers, either path serves. If your application only works with a rate well above the default, plan for the inline path.
Inline PCT is the more efficient architecture, when available, as the update rate can be pushed higher, and the airtime is reduced.
The Bluetooth® word mark is a registered trademark owned by Bluetooth SIG, Inc. Any use of such marks by Metirionic GmbH is referential only and does not indicate any affiliation with, sponsorship, or endorsement by Bluetooth SIG, Inc.
You are currently viewing a placeholder content from Facebook. To access the actual content, click the button below. Please note that doing so will share data with third-party providers.
More InformationYou are currently viewing a placeholder content from Instagram. To access the actual content, click the button below. Please note that doing so will share data with third-party providers.
More InformationYou are currently viewing a placeholder content from X. To access the actual content, click the button below. Please note that doing so will share data with third-party providers.
More Information